Friction drive bicycle engine kits are the easiest engine kits to run and install. Unlike standard “dry clutch” bike engines that mount in the center of your bike and into the wheel, “friction drive” engines simply mount over your rear tire and start as soon as you pull the pull-start rope.
People choose friction drive motors for many different reasons. They’re leaps and bounds easier to install than 2-stroke center-mount engines and 4-stroke engines that require you to change out your bike’s cranks, perfect for people without a lot of time or knowledge. Friction-drive engine kits are also more compatible than other engines because you mount it over the wheel. You’re not stuck using a 26″ wheel beach cruiser- you can use a mountain bike, city bike, or even a road bike with this type of engine.
The Flying Horse 4-Stroke 38cc Lock-n-Load is Flying Horse’s first friction drive engine kit, and it couldn’t be easier to install. Here we’ll show you how to install Flying Horse’s friction drive motor, but this is a pretty universal guide to mounting a friction drive motor if you have a Grubee or Stinger friction drive engines.
To install these engines all you need are these tools:
- Adjustable Wrenches (or a 14mm socket wrench)
- Zip ties
- A box cutter (or a sharp knife)
- A wire stripper
- Electrical tape
- Compact drill with 1mm and 5mm drill bits
Here’s what comes with the Lock-n-Load engine (other engines may come with different mounts):
First you’re going to install the squre-shaped mount that goes on your bike’s seat stay. Place the flat plate underneath the seat stay, the square piece above the seat stay, and hand screw the three bolts and screws in to place. BE SURE THE MOUNT IS CENTERED, and that your bolts are torqued evenly with a socket wrench or adjustable wrenches:
Next it’s time to install the engine to the main mount. Put the bevel side of the cylinder connector on the engine and then the mount on top of that (the brass cup should fit inside of the connector). Hand tighten the 4x black bolts with washers, then torque them down with a wrench in an “X” pattern:
Now we’re going to mount the support brackets on to your bike. Because bikes vary in size you’ll want to make sure you adjust the brackets to allow clearance of the engine mount. Take the nuts off the wheel, install the brackets on each side of the wheel, adjust, and fasten the wheel nuts. Make sure the slots on the wheel brackets go from bottom left to top right diagonally (you won’t be able to throttle properly if they’re the wrong way):
Then mount the engine to the mounting hardware (you might want an extra set of hands for this part, but it’s not absolutely necessary). Take the bolt out of the square mounting bracket, align the front of the mounting plate with the ports on the bracket, and send the bolt through the bracket and plate:
Move to the back of that mounting plate and install the quick-release. Put one bolt in to the engine side of the plate and fasten it with a spacer and nut. Install the long, metal nut on to that screw. After that, do the same with the other end of the bolt (with the quick-release lever) by sending the bolt through the wheel brackets. Then attach the bolts:
Now you install the throttle cable and kill switch. Send the beaded end of the cable through the cable port on the carburetor, then in to the throttle rocker. Run the throttle cable along the frame and zip-tie the cable- BUT DO NOT TIGHTEN THEM ALL THE WAY YET. Take the kill switch and send it along the same path as the throttle cable, with the cable ends toward the engine. Wire the kill switch to the motor (black wire to black wire, red wire to red wire). Once that’s complete tighten the zip ties:
Next you’re going to install the throttle handle. Start by taking off the existing grips (you may need to use a razor to slice the grips in order to pull them off). Once they’re off, take the compact drill and drill a 1mm pilot hole at about 4.25 Inches from the end of the bar. Drill in to that hole with a 5mm drill bit for the kill switch mounting pin:
After that, install your throttle handle in to the kill switch, and install the kill switch on to the handlebar by lining the kill switch notch in to the drilled hole. Bolt the top half of the kill switch around the throttle handle and fasten the screws:
(Note: If you have a gas tank that’s pre-installed on to your motor you’re ready to ride! If you have an external gas tank, just install it as you would with any other engine kit: gas tank on top of your top bar of the frame and brackets below it to secure it to the frame.)
Once you’re done it’s all about tuning. Take out as much slack as you need from the throttle cable by adjusting the tension on the handle and cable port on the engine. If need be, you can also adjust the idle by tightening or loosening your carburetor’s idle screw.
When breaking your motor in we recommend using Maxima 4-stroke Break In Oil for about 100 miles. While you’re breaking it in, make sure to take it easy and vary the RPM’s to ensure a long engine life. After break-in, we recommend using Maxima Pro Plus 10w30 4-stroke Scooter Motor Oil.
Pull the pull start rope and engage the motor to the wheel. It might take multiple times to start, but once it does lower the motor down on to your wheel. To do that, simply unlock the quick-release, move the mounting plate down so that the roller grips the tire (not too hard, but not too soft either), then tighten the quick-release. It make take you a few times to find the sweet spot for that fit, but once you do you’ll know it:
If you’re more of a visual learner, take a look at our Friction Drive bike engine installation video for a step-by-step walk-through of putting one of these motors on your bike. Who knows? You might just ditch that 2-stroke and upgrade to a less stressful form of transportation…